                         June 12, 1967SB-101      Bulletin No:SSB Transceiver
                  SB-101-1D
                                           Driver Oscillates on 40 Meters
Remove C-924 [.02 disc capacitor] from across 150K ohm resistor & delete
from circuit.
------------------------------------------------------------------------------------------------------------------
                                                        November 1, 1967SB-101
 Bulletin No:SSB TransceiverSB-101-2D
                                                           Switch Action
Improvement
DELETE: (2) 253-67    (2) WASHER, .186OD, .054 THICK (1 EA FOR 100-445)
ADD:       (2) C253-67  (1)   "      "            "               "
"    (FOR 100-445)ADD:       (2) B255-79  (1)SPACER, 1/8 SHOULDER, THREADED
ADD:       (2) A263-7    (1)FOOT, FELT, 1/8" THICK
DELETE:(4) 266-91    (1)ACTUATOR, SLIDE SWITCH
ADD:      (4)  266-97   (1)     "      "            "           "
-----------------------------------------------------------------------------------------------------------------
                                                        NOVEMBER 1, 1967SB-101
      Bulletin No:SSB TransceiverSB-101-3D
                                                          Improper Tuning
Delete: [2] 26-109  [2] Variable Capacitor, 2 Sect. P.C. Mtg
Add:    [2] 27-122  [2] Variable Capacitor, 2 Sect. P.C. Mtg
Delete:         [4] 85-131-1 [1] PC Board, RF Driver Mixer [85-131
Screened 605-1225]
Add:    [4] 85-131-2 [1] PC Board, RF Driver Mixer [85-131 Screened605-1616]
Reason for change:  To correct tuning trouble.
-------------------------------------------------------------------------------------------------------------------
                                                           APRIL 18, 1968SB-101
Bulletin No:SSB TransceiverSB-101-4D
                                              Improper Tuning on 40Meters
Description of Change:
DELETE:  (2) B21-31             (50) CAPACITOR, DISC .02 MFD Z5U
ADD      :  (2) B21-31             (49)   "         "          "
       "        "DELETE:  (4) 85-131-1   (1) PC BOARD, RF DRIVER MIXER
ADD      :  (4) 85-131-1   (1) "              "           "          "
REMOVE:  C-424 installed across R-401
NOTE:  SBM-100-1 called for the installation of this capacitor on SB-100
units.  This capacitor should now be removed.
--------------------------------------------------------------------------------------------------------------------
                                                          June 3, 1968SB-101
      Bulletin No:SSB TranceiverSB-101-5D
                                      Grounding Problems on Tranceivers
A quality of factory wired transceivers have been shipped with loose
rivets both at the rear phono sockets & at the final tube sockets.
This is causing a serious grounding problem.  Corrective recommendations
are shown on the attached sheet:
[[[[[[[[[[[[[NOTE:  IF MY INTERPRETATION IS NOT CLEAR - PSE LET MEKNOW]]]]]]]]]
Illustration shows the installation of a ground buss for the rear panel
phono sockets.  It also states that if the final tube socket rivets are
loose, they should be drilled out & eplaced with 6-32 hardware.
-------------------------------------------------------------------------------------------------------------------
                                                           November 25,1970
 SB-101      Bulletin No:SSB TransceiverSB-101-1
                                                                 MeterZeroing
Original 10-147 control tolerance not sufficient to allow zeroing in all
units.  This part is being respecified to a closer tolerance.  In the
meantime, any field problems requarding zeroing of the meter can be
corrected as follows:Change:   R-107 from 100K Ohm to 82K Ohm (1-159).
-------------------------------------------------------------------------------------------------------------------
                                                    September 14, 1972SB-101
      Bulletin No:SSB Transceiver SB-101-2
                                   Repeated Heterodyne Oscillator Failure
Change:  R-212 from 220 Ohm to 330 Ohm 1/2 Watt resister (1-4).
------------------------------------------------------------------------------------------------------------------
                                               May 23, 1974SB-101Bulletin No:
SSB TransceiverSB-101-3
                        SB & HW Series Audio Amplifier & VOX
                                      Circuit Trouble Shooting Guide
It is assumed that the basic steps such as making DC voltage measurement,
checking tubes & reviewing the soldering have been completed.
The following information was compiled from the above transceivers in the
80M LSB position.  The mike level control was at the 9:00 o'clockpoisition.
AC signal voltages are listed below.  These voltages were measured from
the microphone connector through the VOX circuit.  All measurements were
made with a VTVM. A microphone or audio generator for .1V @ 1KHZ can be
used as the signal source.Mike Connector Lug 1                .1VAC
Pin 2 of V1                                     .02VAC
Pin 6 of V1                                     10-15VAC
Pin 6 Level Control                                     10-15VAC
Pin 5 Level Control                                     .5VAC
Pin 9 of V1                                     .2VAC
Pin 8 of V1                                     .1 - .3VAC
Center Arm of VOX Sensitivity Control                   5-15VAC
Pin 7 of V17                                    5-10VAC
Pin 6 of V17                                    40-50VAC
Junction of C211-D201                           40-50VAC
Pin 9 of V12                                    9-15VAC
By tracing the AC signal from stage to stage the point of trouble can be
isolated & steps taken to correct it.POSSIBLE TROUBLE AREAS
- Check each of the shielded cables for a possible open or poorly
grounded shield.- Check for continuity through each of the shielded cables.
- Check for a proper ground at the mike control level.
- If the frequency response of the audio stage is not within
specifications check the values & installation of C1, C2, C3 & C9.
- A change in VOX delay after operating for a period of time can be
caused by leakage in diode D201.  The other possibility is a change in
value of capacitor C213.  Either component could experience a change in
operation characteristics due to heat.
------------------------------------------------------------------------------------------------------------------
                                                          May 23, 1974SB-101
      Bulletin No:SSB TransceiverSB-101-4
                           Diode Leakage in The SB-100, SB-101, HW-101
The silicon diodes used in the SB100 & SB101 are standard power diodes
rated at 500PIV & 750MA.  For each condition described, the diodes should
be replaced with an equal value to maintain proper opration.
1.  Diodes D902 & D903, when leaky, will have an effect on ALC
indication.  The ALC indication will be normal for the first half hour to
an hour.  Then the meter indication will start dropping off until there
is very little indication.
2.  D101, when leaky or defective, will cause slow or no receiver
recovery after transmitting for any period of time.
3.  D905, under leaky conditions, will cause very slow or no receiver
recovery and false meter indications.  The meter will kick up scale &
slowly drift down to zero.
4.  D201 will result in a decrease in VOX sensitivity to the point where
the VOX circuit will not be activated.  It can also result in increasing
VOX delay, causing the relay to stay in the transmit condition.
-------------------------------------------------------------------------------------------------------------------
                                        May 23, 1974SB-101      Bulletin No:
SSB Transceiver                        SB-101-5
                            SB & HW Series Instability & Corrective
                                                            Information
                                           Instability -- Troubleshooting
We suggest you check for each of the following possible causes:
1.  Intermittent, rosin or cold solder joints.
2.  Loose hardware at the tube sockets, terminal strips, circuit boards,
shields and      rear panel sockets.
3.  Poor lead dress at tube sockets V8 & V9.  The component leads must be
short      as possible.
4.  Check C925 (Final tune capacitor) to be sure it is isolated from the
tuning shaft.      This is to prevent RF from traveling on the shaft to
the front panel.
5.  Check all edges of the final enclosures for proper grounding to the
main                chassis.
6.  Check the hardware for the side rails to be sure a good ground is
being                provided.
7.  Be sure that all the ground clips on the coil cover are making good
contact with      the switch shields.
8.  Check the soldering of the switch shields to the center pins of tube
sockets V6,      V7, V10 & V11.
9.  Check the ground leads from the switch board & shields, to be sure
they are           going to ground foil & not to the preselector
capacitor foil pods on the RF driver       board.
10.  Check for broken or shorted pigtails on each of the shielded cables
in the unit.11.  Check RFC801 & L901 for any signs of deterioration or physical
damage, (burn        spots).  If apparent replace the part.
12.  Improper adjustment of the Het. Osc. coils could cause impropermixing
       action, resulting in the final operating at a different frequency
appearing as               instability.
13.  Change driver & final tubes then reneutralize per manualinstructions.
14.  Check driver tube shield to be sure that it has a good ground
contact with the           socket spring clip.
15.  Check for a good ground between the front panel & chassis.
16.  Check the SWR of the antenna system at the frequency of operation.
Should             be below 2:1.
17.  Check the antenna coax for leakage, poor connectors & broken shield
                     connections.18.  Is the transmitter properly grounded?
19.  Be sure all shields & tube shields are installed.
20.  Realign using a properly terminated 50 ohm non-reactive dummy load.
NOTE:          This does not include a light bulb.
21.  Check for normal Het. Osc. test-point voltage.
22.  Check for proper LMO injection voltage 1.0-1.5 VRF.
23.  Check for a high AC ripple content in the LV-B+, HV-B+ and bias
voltages from          the power supply.
24.  Check to be sure that the shafts do not touch each other in theinsulated
        coupling, and that the set screws do not touch the PA shield.
25.  Check to be sure that the PA tune shaft turns the variable capacitor
& is not             slipping in the insulated coupling.
--------------------------------------------------------------------------------------------------------------------
                                        May 23, 1974SB-101      Bulletin No.
SSB Transceiver                        SB-101-6
                       Alternate Method of Neutralizing The Final
                                                              Amplifiers
1.  Disconect final plates & screen grid.***2.  Turn unit on.
3.  Rotate the BAND switch to 28.5.
4.  Place the VTVM RF probe in the ANTENNA connector.**
5.  Set the FUNCTION switch to TUNE.
6.  Rotate the LEVEL control fully clockwise.
7.  Adjust the PRESELECTOR control for a maximum reading on the VTVM.
8.  Adjust the FINAL control for a maximum indication on the VTVM, with
the LOAD      control set at the 50 ohm position.
9.  Using an insulated screwdriver, adjust neutralizing capacitor for a
MINIMUM      indication on the VTVM.
10.  Readjust the neutralizing capacitor for a minimum indication on theVTVM.
11.  Turn the FUNCTION switch to the off position.
12.  Discharge high voltage power supply capacitors.
13.  Reconnect final plates & screen grid.**VTVM & RF probe will be needed.
***To remove screen voltage in SB-100, SB-101, HW-100 & HW-101 disconnect
R920 (100 ohm resistor) from buss wire between pins of V8 & V9.  In the
SB-102 removal of accessory plug is all that's required.  To remove high
voltage in SB-100, SB-101 & SB-102 disconnect red wire at lug 4 (in
Sb-100 lug 3) of terminal strip BK that goes to grommet BL.  In HW100 &
HW101 disconnect red wire going to lug 1 of RF choke in final cage.
NOTE:  Take adequate steps to eliminate any possible contact with B+ or
B+ shorts to chassis after disconnecting wire & resistor.
--------------------------------------------------------------------------------------------------------------------
                                December 18, 1974SB-101      Bulletin No.
SSB Transceiver                        SB-101-7
                            Oscillations or Low Drive
Loose boards cause sporatic self oscillations & unstable RF conditions,
particularly at the high [15 & 10 meter] bands.  The comb brackets which
ahve been used are aluminum & could not be soldered.  Steel brackets are
now available [Part No: 204-2096] & should be used whenever encountered
in the field. Both the switch shields & the driver boards should be
soldered to these brackets.
This change helps to increase grid drive as well as increase stability.
--------------------------------------------------------------------------------------------------------------------
                                        May 2, 1975SB-101      Bulletin No.
SSB Transceiver                                                 SB-101-8
                     Self Oscillations Occurring After Installation
                                                of Steel Comb Brackets
It has been found that in a number of units, self oscillations are still
occurring after installation of both sets of comb brackets [Part No:
204-2096].  To correct the condition, the screws around the RF driver
board must be tightened securely.  Also, the lockwashers between the
circuit board & chassis must be installed, otherwise a good ground is not
assured.  Retightening screws which are already snug will also cause
these oscillations to disappear in units where it is a problem.
--------------------------------------------------------------------------------------------------------------------
                         March 29, 1976SB-101      Bulletin No:SSB Transceiver
                        SB-101-9
                                                      S-Meter Drift
To bring the meter drift to an acceptable level, install the following:
        CHANGE:  R107 from 100K Ohm 1/2 Watt to 100K 1 Watt
                        [PN 1-28-1]
This makes the voltage divider string more stable with temperature
changes caused by internal heating.
This change will be made in future production runs.
------------------------------------------------------------------------------------------------------------------
                         November 15, 1976SB-101      Bulletin No:
SSB Transceiver                        SB-101-10
                                          Low Receiver Sensistivity
Note:  Sensitivity of the unit is worse on the higher frequencies [15] &
[10] meters.Cure:  Diode D907 may be in backwards or banded backwards.
------------------------------------------------------------------------------------------------------------------
                        September 27, 1977
SB-101                                          Bulletin No:
SSB Transceiver                                 SB-101-11
                   Transceiver Oscillates in Transmit with Mic Keyed
+ + + + Information not yet available + + + +
--------------------------------------------------------------------------------------------------------------------
                         February 22, 1978SB-101 Bulletin No:SSB Transceiver
       SB-101-12
                                                   Tuning Erratic
Some of the earlier LMOS can be opened up for service, such as cleaning
the wiper contacts on the tuning cap when tuning becomes erratic.  Some
of these units have fiber washers between the frame of the tuning
capacitor and the worm gear assembly.  Intermittant contact between the
teeth of the gears can change the ground path for the tuning cap and also
cause erratic tuning.  Simply replacing a fiber washer with a metal
washer will give good connection between the tuning cap frame and the
worm gear assembly to eliminate this problem.
------------------------------------------------------------------------------------------------------------------
                         June 5, 1978SB-101Bulletin No:SSB Transceiver
      SB-101-13
                      Relays Remain Energized After Transmit Condition
After keying the transceiver with PTT for thirty to forty seconds, a
positive voltage in 